Urgent leak or storm damage? Call 01638 597994 - answered day and nightUrgent leak? Call 01638 597994
Mildenhall Roofing Specialists
01638 597994 Get a Quote →

Commercial Roofing in West Row

Mildenhall Roofers supplies and installs commercial roofing systems for businesses, farms and industrial buildings in West Row and across the surrounding area.

Urgent leak or storm damage?

Call any time. Calls are answered day and night and passed straight to our roofers.

Call now: 01638 597994
Commercial Roofing · West Row

Expert Commercial Roofing
in West Row

Choosing the Right Material for Your Commercial Roof

The material you choose for a commercial roof affects cost, longevity, maintenance requirements and how well the roof performs over time. There is no single right answer - it depends on the type of building, the roof geometry, your budget and how long you plan to hold the property. This page sets out the main options honestly, including where each one falls short.

We work across West Row, Mildenhall, Holywell Row, Needham Street, Barton Mills, Culford, Cavenham, Lackford, Icklingham, Herringswell, Kentford, Elveden and Risby.

Flat Roof Systems

Torch-On Felt (Built-Up Felt Roofing)

Torch-on felt has been the standard for commercial flat roofs for decades. It is applied in two or three layers using a gas torch to bond each layer to the one below, creating a waterproof membrane across the entire roof surface.

Pros: Lower upfront material cost than alternatives. Well-understood by most roofers, so straightforward to repair if damage occurs. Good for simple flat roof shapes with uncomplicated drainage.

Cons: Shorter lifespan than EPDM or single-ply - typically 10 to 15 years for a two-layer system, up to 20 years for a high-specification three-layer build-up. Seams and laps are potential weak points as the felt ages and contracts. Torch-on work requires careful fire-risk management on site, particularly around timber structures.

Torch-on felt is a practical choice for a budget-conscious repair or a mid-term solution on a building where a full refurbishment is planned within 10 to 15 years.

EPDM Rubber Membrane

EPDM (ethylene propylene diene monomer) is a synthetic rubber membrane supplied in large sheets. It is bonded or ballasted to the roof deck, with seams sealed using adhesive tape or liquid-applied bonding agents.

Pros: Long service life - EPDM membranes commonly perform well for 25 years or more. Highly resistant to UV degradation and temperature extremes. Large sheet sizes mean fewer seams, which reduces the number of potential failure points. Relatively lightweight, so deck loading is not usually an issue. Compatible with most existing flat roof substrates.

Cons: Higher material and installation cost than felt. Puncture resistance is lower than some single-ply systems, so roofs with foot traffic from maintenance personnel need protection boards laid over the membrane. Black EPDM absorbs heat, which can increase cooling loads in a building with minimal insulation beneath the roof.

EPDM is a strong choice for farm buildings, warehouses and industrial units where long-term performance matters more than the lowest possible upfront cost. It is also a sound option when re-roofing over an existing deck that is in reasonable condition.

Single-Ply Membrane

Single-ply systems - including PVC and TPO - are factory-produced sheets typically 1.2 mm to 1.5 mm thick. They are mechanically fixed or fully adhered to the deck, and seams are heat-welded rather than glued, producing a continuous waterproof layer.

Pros: Heat-welded seams are more reliable than adhesive-bonded ones. Available in light colours, which reduce solar heat gain on insulated roofs. Very good lifespan when correctly installed. Suitable for complex roof shapes and penetrations (for pipework, rooflights and plant).

Cons: Higher installation cost than both felt and EPDM. Quality varies between products, and installation requires familiarity with the specific system being used. Not all roofing contractors carry the tooling for heat-welded seams.

Single-ply is particularly well-suited to retail units, office buildings and any commercial flat roof that needs to accommodate multiple service penetrations or where roof access for maintenance is regular.

Pitched Roof Systems for Commercial Buildings

Profiled Steel Sheeting

Galvanised or colour-coated steel sheets with a trapezoidal or sinusoidal profile are the standard covering for agricultural barns and industrial buildings with pitched roofs.

Pros: Fast to install over large spans. Relatively low cost per square metre. Available in a range of profiles and colours. Modern coated steel carries a manufacturer's finish rating of 25 years or more, though the metal itself can outlast that significantly.

Cons: Fixings are a known weak point - the rubber-sealed screws compress the washer when driven, and over 15 to 20 years the rubber degrades, leaving each fixing hole as a potential leak point. Thermal expansion means sheets move, and poorly detailed ridge caps and flashing can pull apart over time. Condensation on the underside of uninsulated steel can cause internal dripping in cold weather.

Fibre Cement Sheeting

Asbestos-cement sheets have long been out of production; modern fibre cement is non-asbestos.

Pros: Less prone to condensation than uninsulated steel. Quieter in rain.

Cons: Brittle - sheets crack under foot traffic or impact. Older asbestos-cement sheets require specialist removal and disposal, which adds cost to any re-roofing project. Not suitable for new-build or full replacement work in most cases. If existing sheets are in sound condition, encapsulation or over-sheeting with steel can avoid removal costs.

Clay and Concrete Tiles on Commercial Pitched Roofs

Some commercial properties - particularly older retail premises and converted farm buildings - have clay plain tiles or pantiles on their pitched roofs. The same principles that apply to domestic tile roofing apply here, but the larger roof areas and gutters mean defects spread more water than they would on a house.

Tile replacement or re-bedding of ridge and hip tiles is straightforward work. A full re-tile on a large commercial pitched roof is, however, a significant cost and is usually only worth doing when the tile condition is poor across the majority of the roof rather than in isolated patches.

What to Ask a Roofer Before You Decide

  • What condition is the existing roof deck in, and does it need replacing before a new covering is laid?
  • What falls does the existing roof have, and are they adequate for the system you are recommending?
  • Are there existing insulation layers, and are they wet or compressed? (Wet insulation must come out before a new membrane goes on.)
  • How will drainage be improved, maintained or added to?
  • What does the specification include - is the price for a two-layer felt system or a three-layer build-up?

Getting clear answers to these questions before any work starts will help you compare quotes on a like-for-like basis and avoid surprises when the roofer is already on site.

Talk to Us About Your Commercial Roof in West Row

If you manage a commercial or agricultural building in West Row or a nearby village and you want an honest assessment of your roofing options, call Mildenhall Roofers to arrange an inspection. We will give you a straight view of what the roof needs and which material system is the best fit for the building and your budget.

Why choose Mildenhall Roofers?

  • Free survey and itemised quote
  • Fixed price - no surprises
  • Local team

Get your free quote

No obligation · We'll call you to arrange a free visit

By submitting you agree to being contacted about your enquiry. No spam, ever.

Urgent leak or storm damage?

Call any time. Calls are answered day and night and passed straight to our roofers.

Call now: 01638 597994