If you're planning a flat roof replacement or significant repair in Isleham, understanding how the job unfolds from start to finish helps you know what to expect and what questions to ask.
Call any time. Calls are answered day and night and passed straight to our roofers.
A proper flat roofing job starts with a thorough inspection of what is already there. Before any price is given, the existing roof needs to be assessed - not just from ground level but up close. This means checking the current membrane for blistering, cracking, lifted edges and ponding marks, and physically testing the deck for soft spots that indicate rot or delamination in the board beneath.
Older decks are often tongue-and-groove boarding rather than modern plywood, and the individual boards can shrink apart over time, leaving gaps that cause movement in the membrane above. Identifying this at inspection stage means the quote reflects the real scope of the job.
The inspection also covers drainage - where does water run to, is the outlet clear, and is there sufficient fall across the roof surface? A flat roof that doesn't drain properly will fail regardless of how good the membrane is. If the fall is wrong, correcting it needs to be part of the plan.
Once the inspection is done, the roofer should be able to tell you clearly what needs to happen. There are broadly three scenarios: a localised repair to a sound membrane, a new membrane over a sound deck, or a full strip-and-replace that includes new decking. Each has a different cost and timescale.
At this stage, the membrane system is also agreed. For most domestic flat roofs - garages, extensions, porches - the practical choice is between EPDM rubber and felt. EPDM suits roofs where minimising seams matters and where a long service life is the priority. High-performance torch-on felt is a proven alternative and is appropriate where the budget is tighter. The choice should be based on your roof's size, its exposure and what you want to spend.
Any roofer worth commissioning will set out what they intend to do in writing before work starts, including the system being installed, what will happen to the existing felt or rubber, and how edge details, upstands and any penetrations will be dealt with.
The deck is the foundation of the whole system. If the existing deck is plywood and it is in sound condition - firm underfoot, no soft patches, no delamination - it can be retained and a new membrane laid over it. If there are areas of rot or swelling, those sections need to come out and be replaced with new plywood before anything else happens.
On a garage roof where the deck has been holding moisture for years, it is not unusual to find that most or all of the boards need replacing. This adds to the cost and the time needed, but laying a new membrane over rotten board is not something any responsible roofer will do. The new membrane would fail in months as the deck continues to break down beneath it.
Once the deck is confirmed as sound, the surface is swept clean and checked for any fixings that are proud of the surface. Any nail heads or screw heads that could telegraph through and damage the membrane from below are punched down or removed. On timber decks, a layer of 18mm or 22mm plywood is sometimes laid over existing boards to create a flat, stable surface before the membrane goes on.
For an EPDM installation, large sheets of rubber are cut to size on the ground and then positioned on the roof. The deck is coated with contact adhesive, the EPDM sheet is folded back over itself and then carefully rolled out into the adhesive, working from one side to remove air. The edges are dressed over the fascia or up the wall, and the terminations are secured with metal trim or bonded with EPDM-compatible adhesive.
For torch-on felt, the work starts with a base layer that is either nailed or bonded to the deck, followed by a cap sheet that is heat-welded using a gas torch. The torch softens the bitumen on the underside of the felt, which bonds it to the layer below. All laps must be fully welded - cold or only partially fused laps are a common cause of early failure on felt roofs.
In both systems, the upstands where the roof meets a wall receive particular attention. The membrane is dressed up the wall to a minimum height of 150mm and terminated under a cover flashing or into a chase cut in the brickwork. This is one of the most critical details on any flat roof; a poorly formed upstand is one of the most common places a flat roof will leak.
The drainage outlet is fitted or refitted once the membrane is in place. On small roofs this is usually a simple flat-roof drain with a collar that bonds into the membrane material. The collar must be sealed absolutely flush with the membrane surface so that water cannot track underneath it.
Lead or aluminium flashings are dressed in wherever the roof meets adjoining walls, chimney stacks or other vertical surfaces. On extensions, this often means cutting a chase in the brickwork with an angle grinder, inserting the top edge of the flashing and pointing it back in with mortar. This step is often skipped or done poorly, and a lifted or unpointed flashing is a straightforward route for water into the building.
Once the membrane is down and all the details are finished, a careful inspection of every seam, edge and upstand is the final check before the scaffolding or platform comes down. Any area that looks borderline gets additional adhesive or welding. Gutters and outlets are checked to confirm water runs freely.
At the end of the job, all off-cuts, old felt, membrane trimmings and broken deck boards are cleared from the site. Any marks left on walls, fascias or gutters from the work are cleaned off. The roof should be left in a condition where you can inspect it yourself without finding obvious debris or loose material.
Mildenhall Roofers covers Isleham and the surrounding area including Mildenhall, Reach, Tuddenham, Cavenham and Herringswell. If you have a flat roof that needs replacing or a repair that has been on your mind, call us to arrange an on-site inspection so we can give you an accurate picture of the work involved.
No obligation · We'll call you to arrange a free visit
Call any time. Calls are answered day and night and passed straight to our roofers.