Urgent leak or storm damage? Call 01638 597994 - answered day and nightUrgent leak? Call 01638 597994
Mildenhall Roofing Specialists
01638 597994 Get a Quote →

Lead Work in Beck Row

If you've noticed damp patches near a chimney, skylight or roof junction at your Beck Row home, failing lead work is one of the most likely causes.

Urgent leak or storm damage?

Call any time. Calls are answered day and night and passed straight to our roofers.

Call now: 01638 597994
Lead Work · Beck Row

Expert Lead Work
in Beck Row

What Lead Work Actually Does on Your Roof

Lead is used wherever two surfaces meet on a roof and a tile or slate alone cannot seal the join. Chimneys, dormer walls, skylights, roof-to-wall abutments, valleys between two roof pitches, and flat roof perimeters all rely on lead to keep water out. When it is installed correctly and dressed to the right Code (Code 4, 5 or 6 depending on the location), lead is one of the most durable materials in roofing. When it is badly fitted or starts to fail, water finds its way in quickly and the damage it causes can be significant.

We carry out lead flashing, valley work and flat roof lead work across Beck Row and the wider Mildenhall area. All lead is dressed by hand on site, fixed correctly and lapped to the appropriate depth so that it sheds water rather than collecting it.

The Warning Signs That Your Lead Work Is Failing

Lead problems do not always announce themselves with an obvious drip through a ceiling. Some of the most costly failures go unnoticed for months because water tracks along rafters or soaks into insulation before it shows up indoors. Knowing what to look for can stop a small repair turning into a much larger one.

Damp or Staining on Interior Walls and Ceilings

A patch of damp near a chimney breast, around a dormer window or on a ceiling close to a party wall is one of the clearest signs that flashing has failed. The staining often appears after heavy rain and dries out in dry weather, which can make homeowners assume the problem has resolved itself. It rarely does. Each wet spell drives more water in, and over time the timbers beneath start to soften.

Cracked or Lifting Flashing

Lead expands and contracts with temperature. If a flashing was not cut into the mortar joint (referred to as "chased in"), or if the mortar it was pointed into has cracked, the edge lifts away from the wall and creates a gap. You can sometimes see this from the ground, particularly on a chimney stack, where the step flashings around the base show daylight between the lead and the brickwork.

Splits along the surface of the lead itself are another sign to look for. These are usually caused by thermal movement cracking lead that was fixed in a single piece rather than in the correct shorter sections. Lead that is laid in runs longer than 1.5 metres without a drip or expansion allowance will eventually split. This is a common installation error and one of the reasons a cheap lead job rarely stays watertight for long.

Rust Staining or Moss Build-Up Around a Joint

Where flashing has lifted even slightly, debris collects in the gap. Moss and algae thrive in the damp environment this creates, and the roots can work the flashing further open over time. Rust-coloured staining on brickwork below a flashing line often points to water tracking down behind the lead and oxidising fixings or ironwork inside the wall.

Efflorescence on Chimney Stacks

White chalky deposits (efflorescence) on brickwork are caused by salts being drawn out as water moves through the masonry. If these deposits appear on a chimney stack, particularly in a ring or band near the flashing line, it strongly suggests that water is getting in at the flashing rather than through the chimney pot or mortar joints at the top.

Visible Gaps or Missing Lead

On older properties, lead is sometimes found to be missing entirely in sections, replaced with mortar or expanding foam by a previous occupant trying to stop a drip quickly. Mortar is not a substitute for lead. It will crack with movement and it cannot flex the way lead does, so it fails relatively quickly. If you can see mortar-only flashings on your chimney, that is a repair waiting to happen.

What Causes Lead Work to Fail?

Understanding why lead fails helps you ask the right questions before any new work is done, so you do not end up in the same position a few years later.

Thermal Movement and Oversized Pieces

Lead moves considerably with temperature change. The industry uses Codes to define the thickness of lead for different applications, and it specifies maximum lengths for each piece precisely because long sections will buckle and split. A correctly installed step flashing is cut from individual pieces, each lapped over the one below. A poorly installed one might be a single rolled piece bent around the corner of a chimney, which will crack within years. On a sunny summer day, a lead roof covering can reach temperatures that cause significant expansion, and on a cold winter night it contracts back. That cycle, repeated thousands of times, is what the correct fixing methods are designed to accommodate.

Poor Original Installation

A significant number of lead failures trace back to the original installation rather than age. Lead that was not chased into the masonry, lead that was fixed with the wrong clips, lead that overlaps by less than the minimum 75mm, and lead that was not dressed tightly to the substrate will all fail sooner than lead that was correctly installed. If a new-build or recently roofed property is already showing damp at the flashings, poor installation is the most likely cause.

Age and Natural Oxidation

Properly installed lead will last many decades. However, very old lead, particularly on Victorian and Edwardian properties, can eventually reach the end of its serviceable life. The surface oxidises to a dull grey and over a very long period the lead itself can become thin or porous. When this happens, replacement rather than repair is the right answer. Patching heavily aged lead is rarely worthwhile because the material around the patch is at the same stage of life and will fail shortly after.

Mortar Failure

Even correctly installed lead relies on the mortar that holds it in a chased joint. If the mortar has cracked or eroded, the lead edge is unsupported and can lift in wind or under the weight of accumulated debris. Re-pointing the joint and pressing the lead back into it can restore the seal, but only if the lead itself is still in sound condition and the correct length.

Physical Damage

Lead is a soft metal and can be damaged by foot traffic during roofing or maintenance work. Deep impressions or cuts in the surface allow water to pool and can accelerate cracking at that point. On flat lead roofs particularly, damage from people walking on the lead without suitable boards is a common cause of premature failure. Any work on or near lead should be carried out with proper access equipment to protect the surface.

Types of Lead Work and What Each Involves

Lead Flashing

Flashing is the strip of lead that seals the join between a roof surface and a vertical feature, such as a chimney, a dormer wall or a parapet. Step flashings follow the line of the tiles up a sloping wall; soaker flashings sit beneath the tiles and direct water outward; apron flashings seal the front face of a chimney at low level. A properly detailed chimney will use several of these in combination, each dressed by hand to follow the shape of the brickwork and the tile profile.

Code 4 lead (1.8mm thick) is the minimum for most flashings. Code 5 is used where there is greater exposure or where the flashing covers a wider area. The correct Code matters because thinner lead in a demanding location will show signs of distress sooner.

Lead Valleys

A valley is the internal angle where two roof slopes meet. Water from both slopes runs into this channel, so the volume of water it carries is higher than any other part of the roof. Lead is the most reliable material for a valley on a tiled or slated roof, and it should be laid in sections with proper drips between them to manage thermal movement. A minimum width of 300mm is needed in a valley to allow for the width of tiles on each side plus clear water flow down the centre. Valleys that are too narrow, or that have been filled in with mortar rather than maintained as a clear channel, collect debris and pond water.

Flat Roof Lead Work

Small flat roof areas, such as bay window tops, outrigger roofs and flat dormers, are sometimes finished in lead, particularly on older properties. Lead for a flat or near-flat area requires correct falls to drain water, proper drips across the width of the roof to manage thermal movement, and correct upstands where the lead meets a wall or parapet. Felt-finished flat roofs have separate requirements, but where lead is the existing material, like-for-like replacement is usually the most appropriate approach.

How the Work Is Carried Out

The first step is an accurate assessment of what is failing and why. Replacing a flashing without identifying the root cause, whether that is mortar failure, incorrect original installation or lead that has genuinely reached the end of its life, means the same problem is likely to recur.

Where the lead is in sound condition but has lifted at a joint, re-dressing and re-pointing can be enough. Where the lead has split, thinned or been badly installed, replacement is the right course. New lead is cut to the correct length and Code, dressed by hand over the substrate using a dresser and bossing mallet to follow every contour, then fixed with the correct clips or wedges and pointed with a suitable mortar or sealant at the chased edge.

All working surfaces should be thoroughly cleaned before new lead is dressed. Moss, lichen and old mortar left under new lead will prevent it from seating correctly and can trap moisture against the substrate.

What Does Lead Work Cost?

Lead work is priced according to the scope of work, the Code of lead required, the access needed and the complexity of the detailing. As a general guide, a single chimney flashing replacement using Code 4 or Code 5 lead typically costs in the range of £350 to £700 depending on the size of the stack and the number of individual pieces involved. A lead valley replacement on a standard semi-detached roof typically falls in the range of £400 to £800. Small flat roof areas in lead are priced by the square metre, with installed costs typically ranging from £80 to £150 per square metre depending on the Code and the detailing required. These are indicative UK ranges; any accurate price needs a survey of the actual job.

Access is a significant factor. Most chimney and valley work requires a scaffold or tower for safe working at height. The cost of access should always be factored into any quote, and it is worth asking specifically whether it is included.

Questions to Ask Before Any Lead Work Is Done

  • What Code of lead is being used, and is it appropriate for this location?
  • Will the lead be chased into the masonry, or surface-fixed only?
  • What are the maximum lengths of individual pieces, and how will thermal movement be managed?
  • Is the existing substrate, including any timber beneath a flat lead area, in sound condition?
  • Is scaffold or other fixed access included in the price?
  • What will be done with the old lead? (Lead has scrap value and should be accounted for.)

A roofer who can answer these questions clearly, without hesitation, is demonstrating that they understand the material and the standards involved. Lead work that is done correctly is a long-term repair. Lead work that is done cheaply often needs attention again within a few years.

Lead Work in Beck Row and the Mildenhall Area

We carry out lead flashing, valley and flat roof lead work in Beck Row and the surrounding villages. If you have noticed damp near a chimney or roof junction, or if you can see lifted or cracked flashing from the ground, call us to arrange a roof survey. We will tell you honestly what needs doing and what, if anything, can wait.

Why choose Mildenhall Roofers?

  • Free survey and itemised quote
  • Fixed price - no surprises
  • Local team

Get your free quote

No obligation · We'll call you to arrange a free visit

By submitting you agree to being contacted about your enquiry. No spam, ever.

Urgent leak or storm damage?

Call any time. Calls are answered day and night and passed straight to our roofers.

Call now: 01638 597994