Urgent leak or storm damage? Call 01638 597994 - answered day and nightUrgent leak? Call 01638 597994
Mildenhall Roofing Specialists
01638 597994 Get a Quote →

Lead Work in Fordham

If you need lead flashing, valley or flat roof lead work carried out properly in Fordham, make sure every piece is dressed by hand to the correct Code.

Urgent leak or storm damage?

Call any time. Calls are answered day and night and passed straight to our roofers.

Call now: 01638 597994
Lead Work · Fordham

Expert Lead Work
in Fordham

What lead work actually involves

Lead is used in roofing wherever two surfaces meet and a watertight joint is needed: around chimneys, where a roof slope meets a wall, in valleys between two pitches, around skylights and roof windows, and on some flat roof sections. It is one of the oldest roofing materials in continuous use, and when it is dressed correctly and fixed to the right Code it will outlast almost everything else on a roof.

The skill is in the dressing. Lead has to be cut, shaped and fixed so that it moves with the building as temperatures change without cracking or lifting. Step flashings, soakers, apron flashings and valley liners all need to be lapped and fixed in specific ways. A piece that looks fine from the ground can be incorrectly fixed, too thin for its location, or dressed over a surface that was not properly prepared first.

We carry out lead flashing, valley work and flat roof lead work in Fordham and the surrounding area. Lead work should be hand-dressed to the correct Code and properly secured.

Why lead work fails

The most common cause of lead failure is not age but poor installation in the first place. Mortar-raked flashings that were never properly pointed, soakers that were cut too short, lead that was dressed cold and cracked, or apron flashings that were not lapped enough. These problems show up as damp patches on ceilings, staining on chimney breasts, or water tracking down inside a wall.

Thermal movement is the other main cause. Lead expands and contracts as temperatures swing, and if a piece is dressed in one long run without proper joints it will eventually crack or pull away from the fixings. Step flashings on a chimney stack are a typical example: each step should be a separate piece dressed into the mortar course individually, not one long strip bent around the corner.

Age does eventually catch up with lead, particularly in sections that were installed in a low Code for the application. Lead used on a chimney flashing or a valley needs to be Code 4 or Code 5 as a minimum. Thinner lead stretches and splits faster under thermal stress.

Typical costs for lead work in Fordham - and what changes the price

Cost is often the first question homeowners want answered before they decide what to do, and it is a fair one. Lead work pricing varies considerably depending on the type of job, the location on the roof, how accessible it is, and how much old lead needs to be stripped and disposed of. The figures below reflect typical current UK rates for domestic lead work.

Chimney flashing

A full chimney flashing replacement on a standard domestic stack - front apron, two sets of stepped soakers and cover flashings, and a back gutter - typically costs between £400 and £900. The variation comes from the size of the stack, the pitch of the roof, how high the chimney sits, and whether the brickwork needs any re-pointing around the chase. Scaffold or specialist access equipment adds cost on anything above first-floor height.

If only one face is leaking and the rest of the lead is sound, a partial repair to the apron or a single run of step flashing can be done for considerably less. A roofer should inspect all faces while they are up there, though, because problems on one side often point to stress across the whole stack.

Valley lead

Lead valleys on a domestic roof typically cost between £350 and £800 to replace, depending on the length of the valley and the tile type either side. Interlocking concrete tiles need a different approach from plain clay tiles because the overlap geometry is different. A valley that has been patched repeatedly with mortar or lap seal tends to need a full strip because the underlying boarding and underfelt often has hidden damage.

When a valley is leaking it is not always obvious from inside the loft which valley is the source. Water travels along rafters and battens before it drips, so the visible damp patch can be some distance from where the water is getting in.

Flat roof lead

Lead used on small flat roof sections - bay tops, porch roofs, dormers - is priced by area. Expect to pay in the region of £80 to £150 per square metre for stripped and re-laid lead, depending on the Code specified and how the edges are detailed. A typical bay top in the region of 3 to 4 square metres would therefore sit in the £250 to £600 range for lead alone, before any timber or felt remediation work underneath.

Code 5 lead costs more than Code 4 as a raw material but is specified where the lead is fully exposed on a flat or low-pitch surface, because the greater thickness resists thermal fatigue better over time. Using the wrong Code is a false economy.

Individual flashings and soakers

Replacing a single apron flashing at the base of a chimney or around a soil pipe typically costs between £120 and £280 depending on size and access. Roof window and skylight flashings, which are often purpose-designed lead systems, sit in a similar range. Soakers behind individual tiles along a abutment wall are less material but more time to dress and bed, so labour is the main cost driver.

What pushes costs up

Access is the single biggest variable. A chimney or valley that sits at ridge level on a two-storey house requires either scaffold, a scaffold tower, or a mobile elevated work platform. Scaffold erected just for a lead job on a chimney can cost as much as the lead work itself on a small job. It is worth checking whether any other roofing work needs doing at the same time so that the access cost is shared across multiple items.

Hidden damage under the lead adds cost. Boards on a flat roof section may be rotten. Valley boards may have split. The mortar bed in a chimney chase may have crumbled back further than expected. None of this is visible until the old lead is stripped, and any reputable roofer will tell you that a fixed price before stripping is difficult to hold if the timber underneath turns out to be damaged.

The Code of lead specified also affects price. Code 3 costs less per kilogram than Code 5, but using a lighter Code than the application requires means the lead will fail sooner. On exposed rooflines or south-facing slopes that take heavy sun, the thermal cycling is more aggressive and a heavier Code is the right call.

Waste disposal is another factor. Old lead has scrap value, and on larger jobs this can offset some of the material cost, but on smaller repairs the disposal and handling still takes time.

What keeps costs down

Catching a lead problem early is the most effective way to keep the cost manageable. A flashing that has lifted by a few millimetres and let water track in for one winter is a repair job. The same flashing ignored for three winters may have allowed water into the roof structure, and the repair now includes timber work, re-felt and possibly internal decoration.

Combining lead work with other roofing jobs reduces the total access cost. If you are already having tiles repaired or a ridge re-bedded, it makes sense to have lead work inspected and dealt with at the same time while the roofer is already set up on the roof.

Choosing the correct Code for the job from the outset avoids having to redo work in five years. Cutting material cost by using a lighter Code than the Lead Sheet Association recommends is a short-term saving that usually costs more to fix later.

How to get an accurate quote

A quote for lead work should always follow a physical inspection. No one can give you a reliable price from a description over the phone or from photographs alone, because the condition of the substrate and the extent of any damage underneath are not visible until the old material is stripped or the lead is lifted.

When you are getting quotes, ask specifically what Code of lead is being specified and why. Ask whether the price includes new soakers or just cover flashings. Ask how the edges will be fixed and pointed. These are not trick questions; a roofer who knows the work will answer them without hesitation.

Be cautious of any quote that is significantly lower than others without a clear explanation. Lead is not a cheap material, and dressing it correctly takes time. A price that looks too good usually means thinner lead, fewer soakers, or mortar pointing where proper chasing and wedging should be used.

What a properly completed lead job looks like

Good lead work sits neatly against the surface it is flashing, follows the lines of the tile courses, and is dressed tight without visible gaps. The joints between individual pieces should be lapped in the direction that water runs - never lapped the wrong way. Where lead is chased into mortar, the chase should be raked cleanly and re-pointed with mortar, not filled with silicone.

Lead clips or tacks should be used on wider sections to prevent the lead from slipping down the slope over time. On a flat section, drips and welts at the edges should be properly formed to direct water away from the substrate rather than letting it sit on timber.

When the job is done you should be able to see clean lines, proper laps and neat pointing. If the mortar pointing is smeared across the face of the lead rather than packed into the chase, that is a sign of a rushed finish. Ask to see the work while the roofer is still on site if you can.

Lead or alternative flashing materials

Lead is not the only option for flashings. Aluminium and zinc flashings are available, as are lead-effect alternatives made from composite materials. These are cheaper per metre but they do not perform identically to lead. Lead is self-healing to a degree: minor surface scratches oxidise and seal over. It is also softer and easier to dress tightly into irregular surfaces.

In most domestic applications, lead remains the material of choice for quality work because of its longevity and workability. Substitute materials may be appropriate in some situations, but if you are replacing flashings on a chimney or valley that was originally leaded, re-leading is almost always the better long-term answer.

Get a lead work quote for your property in Fordham

If you have a damp patch that might be a flashing problem, or you know your lead needs attention, call Mildenhall Roofers to arrange a roof inspection. We cover Fordham and nearby villages, and you should expect a clear assessment of what needs doing and what it is likely to cost before any work starts.

Why choose Mildenhall Roofers?

  • Free survey and itemised quote
  • Fixed price - no surprises
  • Local team

Get your free quote

No obligation · We'll call you to arrange a free visit

By submitting you agree to being contacted about your enquiry. No spam, ever.

Urgent leak or storm damage?

Call any time. Calls are answered day and night and passed straight to our roofers.

Call now: 01638 597994