Urgent leak or storm damage? Call 01638 597994 - answered day and nightUrgent leak? Call 01638 597994
Mildenhall Roofing Specialists
01638 597994 Get a Quote →

Lead Work in Icklingham

When lead work fails on a property in Icklingham, the question that follows quickly is whether to repair what is there or replace it entirely - and getting that decision right saves money and prevents repeat problems.

Urgent leak or storm damage?

Call any time. Calls are answered day and night and passed straight to our roofers.

Call now: 01638 597994
Lead Work · Icklingham

Expert Lead Work
in Icklingham

What Lead Work Actually Involves

Lead is used in roofing wherever two surfaces meet and need a weathertight seal. That means flashings where a roof meets a chimney or a wall, valleys where two roof slopes run together, and on flat roof areas where lead sheet is dressed over the surface. It is one of the oldest roofing materials in use and, when properly installed, it outlasts almost everything else on a roof.

The quality of lead work depends entirely on the skill of the person carrying it out. Lead must be dressed by hand to follow the shape of the surface beneath it. It must be cut to the correct Code for the application - thinner lead (Code 3 or 4) for flashings, heavier Code (5 or 6) for valleys and flat areas - and it must be fixed in a way that allows for thermal movement without cracking or pulling free. A lead flashing that has been nailed solid rather than clipped, or dressed cold rather than worked properly, will fail within a few years regardless of how good the lead itself is.

Lead work should always be dressed by hand to the correct Code and properly secured. We carry out lead flashing, valley work, and flat roof lead work for homeowners in Icklingham and the surrounding area.

The Core Question: Repair or Replace?

This is the decision that matters most when a homeowner calls about a lead problem. Repair and replacement are not interchangeable options - each is right in different circumstances, and choosing the wrong one either wastes money or stores up a bigger problem for later.

A common mistake is to patch failing lead when the underlying cause has not been addressed. Equally common is replacing lead that was structurally sound and could have been fixed at a fraction of the cost. Understanding the difference starts with looking honestly at what has gone wrong and why.

When Repair Makes Sense

Repair is the right answer when the lead itself is still in good condition but something specific has failed. The most common candidates for repair are:

  • Pulled or lifted flashings. Chimney flashings and step flashings are often held into mortar joints with wedges and sealant. Over time, the mortar erodes, the lead lifts out of the joint, and water gets in. The lead itself is fine - it just needs to be re-secured, the joint raked out, and fresh mortar or leadmate applied. This is a repair job, not a replacement.
  • Cracked sealant at the edges. Some older installations relied too heavily on mastic or sealant rather than proper dressed joints. When the sealant fails, it can look alarming but the lead underneath may be intact. Cleaning the joint and applying fresh sealant, or better still re-dressing the edge properly, is sufficient.
  • Small splits or pin holes. Lead can develop small cracks or pin holes over many decades, particularly in areas of thermal stress. If the surrounding lead is still thick and pliable, these can be repaired using lead welding or by burning in a small patch. The patch must be properly bonded, not just stuck over the surface.
  • Isolated mechanical damage. Damage from a falling branch, a poorly placed ladder or a previous repair that has failed in a localised spot can often be addressed without replacing the whole run of lead.

As a general principle, lead in good original condition - pliable, of adequate thickness, correctly installed - is worth repairing. Lead sheet can last 60 to 100 years when it was properly installed in the first place. If the lead on your property was put down correctly and only a section has failed, repair preserves the rest of that working life.

Repair costs vary depending on the nature and extent of the work. Reflashing a chimney where the lead has simply pulled from the joint typically costs in the range of £150 to £400, depending on the size of the chimney and the amount of lead involved. A localised patch repair to a valley or flat area is usually at the lower end of that range. These figures reflect current UK pricing and will vary by job.

When Replacement Is the Right Call

Replacement is not always the more expensive choice in the long run. Repeatedly repairing lead that is fundamentally worn out or incorrectly installed costs more over time than replacing it properly once.

There are clear signs that replacement is the better option:

  • The lead is brittle or crystallised. Lead that has been in place for a very long time, or that was exposed to chemical attack, can become brittle. It loses its ability to move with thermal expansion and contraction, and it cracks. Patching brittle lead is short-term at best. It will crack again nearby, usually within a year or two.
  • The lead is the wrong Code for the application. Light-gauge lead (Code 3) is sometimes used in positions that need Code 4 or Code 5. This is an installation error. The lead is thin, it has stretched and cracked, and no amount of patching will fix the fact that it was never heavy enough for the job. The only lasting solution is to strip it and install the correct Code.
  • The lead was never properly dressed. Poor original installation shows in several ways: lead nailed rather than clipped, inadequate overlaps at joints, lead forced into shape cold rather than worked, or insufficient upstand against a wall. These are not things that can be repaired. The whole installation needs to come out and be done properly.
  • Failure is occurring in multiple places at once. If you are getting leaks from different sections of the same run of lead, or if patches are failing shortly after being applied, the lead is at the end of its life. Selective repair at this point is uneconomic - the next failure is already on its way.
  • There is damage to the substrate beneath. If water has been getting in for a while, the timber or deck beneath the lead may be rotten or saturated. In that case, the lead must come off anyway to address the substrate, and it makes sense to lay new lead at the same time rather than re-dress old material over repaired timber.

Replacement costs for lead work depend heavily on the area covered and the Code of lead required. A full chimney reflash, stripping the old lead and installing new, typically costs between £400 and £900 for a standard chimney. Lead valley replacement on a medium-sized roof section can range from £600 to £1,500 or more depending on length and access. Flat roof lead replacement is priced by the square metre, and for Code 5 lead the material cost alone is significant, so expect total costs from around £80 to £150 per square metre including labour and preparation.

How to Tell Which Situation You Are In

You cannot always tell from the ground or from inside the loft. A patch of damp on a ceiling tells you water is getting in - it does not tell you where from, or why. Lead failure is one cause, but not the only one. Checking the lead properly means getting up to it, looking at the condition of the material, testing whether it is still pliable, checking the fixings and joints, and looking at what is happening at every potential entry point nearby.

If a roofer looks at your property and immediately recommends full replacement without being able to explain why repair is not appropriate, that is worth questioning. Ask what condition the lead itself is in, what Code it is, and why the failure has occurred. A good roofer should be able to answer all three. Equally, if repair is recommended, ask how the underlying cause of the failure is being addressed - not just the visible gap or crack.

Lead Flashings: What a Good Job Looks Like

Flashings are the most visible part of lead work on most domestic properties. They run along the base of chimneys, up the sides of chimneys (step flashings), along the junction between a roof slope and a parapet wall, and where a pitched roof abuts a vertical wall.

A properly installed flashing is dressed neatly against the surface below, with a consistent upstand of at least 75mm against any vertical surface, and fixed using lead clips or tacks rather than being nailed through. Where the flashing enters a mortar joint, it is wedged in with lead or plastic wedges and pointed with a flexible mortar. The overlap between adjoining pieces of lead should be at least 100mm. These are not optional details - they are what determines whether the flashing lasts or fails within a few years.

On older properties, flashings are sometimes found to have been bedded in bitumen rather than properly fixed. This can hold for a time but it is not a long-term solution. Bitumen becomes brittle in cold weather and soft in heat, and it does not accommodate the movement that lead needs to make.

Lead Valleys: Why They Matter

A valley is the internal angle where two roof slopes meet. It carries a significant volume of water off the roof, especially during heavy rain. Lead valleys need to be sized correctly for the area of roof they are draining, and they need to be laid with proper overlaps - a minimum of 150mm on shallow pitches, more on steeper ones.

A poorly installed or deteriorating lead valley is one of the more serious lead problems on a domestic roof because the volume of water involved means that even a small gap allows a large amount of water in. Clay or concrete tiles used in close-mitred valleys (where there is no separate valley material) are an alternative, but on many properties a lead valley is the correct original detail and the right repair or replacement material.

Lead valley replacement is not a quick job. The tiles on either side of the valley need to be carefully removed, the valley boards checked and replaced if necessary, the new lead laid in correctly sized bays with proper overlaps, and the tiles re-bedded and pointed on each side. Cutting corners on any of these steps leads to early failure.

Flat Roof Lead Work

Lead is used on flat and low-pitched roof areas, typically on bay window tops, porch roofs, and small projecting sections. For these applications, Code 5 or Code 6 lead is standard. The lead must be laid in bays no longer than 1.5 metres to allow for thermal movement, with proper drips at changes of level and dressed overhangs at the edges.

A flat lead roof that was laid in one continuous sheet - no bays, no drips - will crack. Lead expands and contracts significantly with temperature change, and without the ability to move freely it splits. This is a very common cause of failure on bay tops and porch roofs. The fix is not to patch the cracks but to strip and relay the lead correctly with proper bays.

EPDM rubber is a common alternative for small flat areas and is lower in upfront cost. Lead remains the material of choice where a traditional appearance is required or where the roof detail is complex, because it can be dressed to any shape. Both materials, properly installed, perform well - the choice depends on the property and the homeowner's priorities.

What to Expect During Lead Work

For most domestic lead work jobs, access is by scaffold or tower - ladder access alone is not adequate for a proper job on a chimney or valley. If a contractor proposes to re-flash a chimney from a ladder without any other means of safe access, that should give pause for thought. Working at height safely requires stable access, and cutting corners on access usually means cutting corners on the work.

The old lead, if it is being replaced, is scrap and has a residual metal value. A good roofer will take the old lead away and account for it. If you are having a substantial amount of lead replaced, it is reasonable to ask whether the scrap value has been factored into the quote.

Good lead work takes time. Dressing lead properly, cutting step flashings to follow a course of brickwork, forming soakers behind tiles - none of these can be rushed without the quality suffering. If the price you are quoted seems very low for the scope of work described, that is a signal to ask exactly what is and is not included.

Lead Work in Icklingham and the Mildenhall Area

Mildenhall Roofers carry out lead flashing, valley, and flat roof lead work in Icklingham and across the surrounding area. If you have a leak that you suspect is coming from lead, or if you can see that flashing has lifted or cracked, the right starting point is a proper look at what is there before any decision is made about repair or replacement.

Call us to arrange a roof inspection and we will give you a straight answer about what needs doing and why - repair where that is the honest recommendation, replacement where it is not.

Why choose Mildenhall Roofers?

  • Free survey and itemised quote
  • Fixed price - no surprises
  • Local team

Get your free quote

No obligation · We'll call you to arrange a free visit

By submitting you agree to being contacted about your enquiry. No spam, ever.

Urgent leak or storm damage?

Call any time. Calls are answered day and night and passed straight to our roofers.

Call now: 01638 597994