If you need lead flashing, valley repairs or flat roof lead work in Lakenheath, make sure the work is carried out by hand to the correct specification.
Call any time. Calls are answered day and night and passed straight to our roofers.
Lead is used in the parts of a roof where two surfaces meet or where the roof meets a wall. Chimneys, bay windows, dormers, valleys between two roof pitches, parapet walls and flat roof upstands all rely on properly dressed lead to keep water out. When that lead fails, water tracks silently into the structure for months before you notice a stain on the ceiling.
Good lead work is not simply a matter of cutting and pressing a piece of sheet lead into position. The lead must be the right code for the application, dressed by hand to follow the profile of the surface beneath it, lapped at the correct depth, secured without restricting its natural thermal movement, and pointed where it meets masonry. Each of those steps matters. Miss one and you have a joint that will open up within a few years.
We carry out lead flashing, step and cover flashings, valley work and flat roof lead detailing across Lakenheath and the surrounding area.
A common problem is lead that has been secured with mortar alone and nothing else. Mortar does not bond permanently to lead because the lead expands and contracts with temperature changes. Over time the mortar cracks and lifts, the lead lifts with it, and rainwater runs straight in behind the flashing.
Another common failure is lead that is too thin for the job. Lead sheet is sold in codes from Code 3 upwards. Code 3 is the lightest and is generally only appropriate for internal gutters and soakers under a heavier covering. Chimney flashings and valley linings need Code 4 or Code 5 as a minimum. Using the wrong code saves a little money at installation but shortens the life of the work considerably and makes splits and pinholes more likely as the thinner material fatigues with movement.
Lengths that are too long are also a problem. Lead should be dressed in sections no longer than 1.5 metres because a longer piece will ripple, buckle and eventually crack as it expands in summer heat and contracts in cold weather. Some roofers cut and fit a single long run to save time. It looks neater when first done but rarely lasts as long as it should.
Finally, poorly formed joints at laps and upstands allow water to be drawn in by capillary action. The lap needs to be deep enough and the upstand needs to reach at least 75mm above the roof surface. Short upstands are cut corners that show up in wet weather.
Lead flashing is fixed to the wall or chimney by being tucked into a raked-out mortar joint, then secured with lead wedges and pointed with fresh mortar. The lead is then dressed down over the junction and lapped onto the roof covering by a minimum amount that depends on the pitch. On a shallow-pitched roof that lap needs to be greater to prevent wind-driven rain getting underneath.
Step flashings are used where a roof slopes alongside a wall, such as at a side extension or where a lean-to meets the main house. Each step is cut individually to match the gauge of the tile or slate, overlapped with the one above it, and dressed into successive mortar joints. It is fiddly, time-consuming work, and the quality of a step flashing job is easy to assess: each step should sit flat and tight, with no visible gaps at the wall face.
Counter flashings or cover flashings are a second layer that fits over the top edge of the base flashing and tucks into the wall separately. They allow the lower flashing to move independently of the masonry, which is particularly useful on older properties where the mortar is softer and more prone to movement.
Valleys are the internal angles formed where two pitched roof sections meet. They carry a heavy volume of rainwater from both slopes down to the gutters, and they are under constant stress from the volume of water, debris build-up and thermal movement. A lead-lined valley done properly will outlast many of the tiles around it. One done badly will fail early and cause water damage to the roof timbers underneath.
For a lead valley, the underlying boards need to be sound and the lead needs to be laid in sections with correct laps. The tile or slate edges on either side are trimmed to a consistent angle and bedded appropriately so that water is guided into the valley channel and not behind the tiles. The width of the exposed lead channel in the valley depends on the pitch: shallower pitches need a wider channel to handle the water flow without it climbing the sides under pressure.
Some valleys are lined with other materials as a cheaper option. A lead-lined valley, done correctly, typically lasts several decades before needing attention. It is one of those parts of a roof that is worth doing properly the first time, because the cost of stripping and relining a failed valley is not small.
Lead is also used at the edges and abutments of flat roofs, even where the main waterproof covering is EPDM rubber or built-up felt. The upstand where a flat roof meets a wall is a critical point: it needs to be sealed in a way that allows both the flat roof covering and the wall to move independently. A lead flashing over the top of the upstand, tucked into the wall, is the traditional and reliable solution.
Drips and weatherings on flat roofs may also be formed in lead. A drip prevents water from tracking back under the roof edge by gravity. It needs to be formed at the correct angle and to the correct depth. Where a flat roof abuts a parapet, the lead flashing needs to cover the full height of the upstand and be turned into the wall high enough to keep water out even in driving rain.
This is the part most homeowners are not told after a lead work repair or installation, and it is probably the most useful section on this page. Lead work that is correctly installed will last a long time, but it is not maintenance-free, and small issues that are caught early are far cheaper to fix than the water damage that follows if they are left.
A visual check of your lead flashings and valleys once a year, ideally in autumn before the wet weather sets in, is genuinely worthwhile. You do not need to get on the roof to do this. A pair of binoculars from the garden or from an upstairs window is enough to spot the most obvious problems. Look for lead that has lifted away from the wall, mortar pointing that has cracked or dropped out, and any section of lead that appears to have moved out of position or buckled.
After any period of very cold weather, it is worth checking again. Lead can contract enough in a hard frost to pull away from a mortar joint that was already marginal. If you see daylight between the lead and the wall at any point, that joint needs attention before the next rain.
Valleys are worth checking after any significant storm or after leaf fall in autumn. A blocked valley is one of the most preventable causes of roof leaks. Debris builds up in the channel, backs up the water level and eventually forces water under the edges of the tiles on either side. Clearing the valley channel of leaves and moss every autumn takes ten minutes and can prevent a repair bill of several hundred pounds.
Moss growing on or near lead flashings is more of a problem than it looks. As moss holds moisture against the lead it accelerates the natural process of lead oxidation at the surface, and the roots can work into the mortar joint and loosen the pointing. A biocidal wash applied to the surrounding tiles and the lead surface once every few years keeps this in check. Do not use a pressure washer directly on lead flashings: the force can dislodge pointing and lift lapped edges.
The mortar pointing that seals the top edge of a lead flashing into a wall joint is often the first part to fail. Mortar has a finite life and will need to be raked out and repointed at some point. When the pointing is repointed, this is also the time to check that the lead wedges are still in place and that the lead itself is still sitting correctly in the chase. Repointing over deteriorated or lifted lead without addressing the lead itself is a short-term fix that will fail again.
The right mortar mix for repointing lead flashings is an important detail. A mix that is too strong (cement-heavy) will shrink and crack as it cures, and will not flex with the lead's movement. A softer lime-based mix, or a proprietary lead flashing sealant where access makes traditional pointing impractical, is more appropriate. Ask your roofer what mix they plan to use before the work starts.
If you can see a ceiling stain directly below or downhill from a chimney, a valley, a dormer or any roof-to-wall junction, that is likely to be a lead work failure. Do not wait for the stain to grow. Water in a roof structure causes damage at a faster rate than most people expect: timbers soak up moisture, rot begins, and plaster or ceiling boards can delaminate long before the surface stain tells you the full story of what has happened above.
A damp smell in a loft after rain, even with no visible stain on the ceiling below, is worth investigating. Get into the loft with a torch during or just after heavy rain if you can do so safely, and look for the point where water is entering. Identifying the exact entry point and describing it to your roofer saves time and helps them bring the right materials first visit.
Not every lead flashing failure needs a full replacement. A flashing that has simply lost its pointing but is otherwise in good condition can be re-wedged and repointed at modest cost. A section of lead that has split or perished needs to be cut out and replaced. A flashing that was installed in the wrong code or with the wrong dimensions needs to come off and be done again properly, because patching a fundamentally wrong piece of lead work is a temporary measure at best.
When you get a roofer out to look at a lead work problem, there are a few specific questions worth asking. Ask what code of lead they are planning to use for each element of the job. Ask how they will secure the lead into the wall - wedges and pointing, or will they use sealant instead (sealant alone is not best practice for a permanent flashing). Ask what the maximum lengths of each section will be. And ask whether the existing lead is worth retaining or whether it needs to come off entirely.
These are not difficult questions, and a roofer who has done this work properly will answer them without hesitation. If you get a vague response, or if the quote does not mention the code of lead being used, those are reasons to ask again or to seek a second opinion.
Lead work pricing varies depending on the complexity of the detail, the access required and the amount of lead involved. As a general guide, straightforward chimney flashing repairs in the UK typically cost in the range of £150 to £400 depending on the extent of the work and whether scaffolding or a tower is needed. A full re-flash of a chimney stack with new lead, repointed joints and new soakers can cost £400 to £800 or more on a larger stack.
Valley relining in lead is a larger job. A single valley on a standard semi-detached house might cost in the range of £500 to £1,200 depending on the length, the pitch and the access. Flat roof abutment flashings are priced similarly to chimney work and depend heavily on the linear meterage involved.
These figures are intended as a starting point for budgeting, not fixed prices. The condition of the underlying structure, the need for scaffolding and the specific detail required all affect the final cost. Any quote should specify the code of lead, the scope of work and what is and is not included.
If you have a suspected lead work failure, a damp patch near a chimney or valley, or you want lead work checked before winter, call Mildenhall Roofers for a roof survey. Lead work in Lakenheath should be carried out by hand to the correct specification. Do not leave a lead work problem through another wet season - the structural drying costs after prolonged water ingress are nearly always more than the repair itself.
No obligation · We'll call you to arrange a free visit
Call any time. Calls are answered day and night and passed straight to our roofers.