Urgent leak or storm damage? Call 01638 597994 - answered day and nightUrgent leak? Call 01638 597994
Mildenhall Roofing Specialists
01638 597994 Get a Quote →

Lead Work in Red Lodge

If water is finding its way in around a chimney, dormer or roof junction on your Red Lodge home, failed leadwork is the most likely cause.

Urgent leak or storm damage?

Call any time. Calls are answered day and night and passed straight to our roofers.

Call now: 01638 597994
Lead Work · Red Lodge

Expert Lead Work
in Red Lodge

Why Lead Work Matters on Your Roof

Lead is the material roofers reach for when they need a watertight joint that will last for decades. Properly dressed lead sheet, fitted at a chimney, valley, dormer or flat roof abutment, will outlast most other roofing materials by a significant margin. The problem is that when leadwork fails, it rarely fails obviously. Water sneaks in gradually, often tracking a long way from the entry point before it shows up as a damp patch on a ceiling or wall.

For homeowners in Red Lodge, and the neighbouring towns and villages served by Mildenhall Roofers, understanding what good leadwork looks like, and what bad leadwork looks like, gives you the best chance of catching a problem before it causes serious internal damage.

Warning Signs That Your Leadwork Needs Attention

The earliest signs of failing leadwork are easy to miss or misattribute. Most people assume a damp ceiling means a broken tile, when in reality the tiles are fine and the problem lies at a junction. Here are the most common indicators that the lead on your roof is worth investigating.

  • Damp patches near chimneys or dormers. If damp appears on a ceiling or wall close to a chimney breast, and there is no obvious broken tile above, the chimney flashing is the first thing to check. Water that enters at a poorly sealed flashing runs down inside the stack and surfaces some distance from where it entered.
  • Staining on internal chimney breasts. A tideline of brown or yellow staining on plasterwork around a chimney breast, particularly after heavy rain, points strongly to a flashing failure rather than condensation or rising damp.
  • White or grey streaks on the chimney exterior. Efflorescence, the powdery white deposit that appears on brickwork, is caused by water repeatedly moving through the masonry and depositing salts as it dries. It tells you that water has been getting in, often at the flashing joint, for a sustained period.
  • Lead that has visibly lifted, cracked or pulled away. If you can see the flashing from the ground with binoculars, look for sections that have curled at the edges, cracked across the surface, or separated from the masonry. Any gap between the lead and the surface it is fixed to is a point of entry for water.
  • Missing mortar in stepped or cover flashings. Traditional flashings are tucked into raked mortar joints and pinned in place, with mortar pointing over the top. When that mortar cracks or falls out, the flashing lifts and water gets behind it. This often looks like a minor cosmetic issue but it is not.
  • Damp that appears only in winter or after specific weather. Leadwork failures are often intermittent. If a damp patch appears after driving rain from a particular direction, or only in the coldest months, that pattern points to a physical entry point rather than condensation.
  • Rust marks or wet patches in a loft space. During a loft inspection, dark wet patches on the felt or insulation directly beneath a chimney or valley are a clear sign that water has been entering at those junctions.

What Causes Leadwork to Fail

Lead is a long-lasting material, but it is not indestructible, and several things will shorten its life or cause it to fail prematurely. Knowing the causes helps you understand what a roofer should be addressing, not just patching over.

Thermal Movement

Lead expands and contracts significantly with temperature. A sheet of lead fitted in summer will be noticeably smaller on a cold winter morning. If the lead has not been dressed and fixed in a way that allows for this movement, it will eventually crack, pull away from fixings, or split along fold lines. This is one reason why the British Standard for leadwork sets out code numbers for sheet thickness according to the width of the piece being fitted. Thinner lead is used for smaller sections where movement is limited, heavier lead for wider sections. A piece fitted without regard to movement will eventually fail regardless of how neatly it looks on the day it was installed.

Nail Sickness and Corrosion at Fixings

Lead sheet is fixed using clips or tacks, and over time those fixings can corrode or pull free. When a clip fails, the lead is no longer anchored and begins to lift and slide. Galvanic corrosion, where dissimilar metals are in contact with each other and with moisture, accelerates this process. Stainless steel or copper fixings are the correct choice for leadwork; ferrous fixings will eventually corrode and leave the sheet unsecured.

Poor Original Installation

A common problem is leadwork that was installed cheaply, without sufficient overlap, without correct drips or steps, or using undersized lead. Code 3 lead, which is the thinnest commonly available, is only appropriate for small pieces. Using it for chimney back gutters or wide flashings to save cost is a false economy. The material will crack and pull within a few years, and the repair cost will exceed the original saving.

Mortar Joint Failure

Where leadwork is tucked into raked joints and pointed over, the mortar is a structural part of the fixing. Lime mortar, used in older properties, is flexible and long-lasting but eventually erodes. Cement mortar, sometimes used to repoint, can be too rigid and may crack as the masonry moves, taking the flashing with it. When mortar pointing over a flashing fails, the flashing is no longer held, and the first gust of wind or thermal cycle will lift it.

Age and Metal Fatigue

Lead that has been on a roof for forty or fifty years has been through tens of thousands of cycles of expansion and contraction. Even well-fitted lead will eventually develop hairline cracks at folds, particularly at corners and where the sheet has been dressed into a complex shape. This is normal material fatigue rather than a workmanship failure, and at this point the correct answer is replacement rather than patch repair.

Tree and Moss Growth

Moss, lichen and tree debris hold moisture against leadwork for extended periods, accelerating surface oxidation and encouraging water to pool at edges rather than run off. In sheltered positions, moss can grow under the edge of a flashing and physically lever it away from the surface over time. Clearing debris and treating moss growth is a worthwhile part of roof maintenance, particularly around chimneys and in valleys.

Where Lead Is Used on a Typical House Roof

Understanding where lead appears on a roof helps you know what to ask a roofer to check, and helps you assess whether a quote addresses the right areas.

  • Chimney flashings. Most chimneys require several separate pieces of lead, including the apron flashing at the front, stepped flashings on each side (step and cover, or soaker and cover depending on the tile type), and a back gutter at the highest point. Each piece needs to be correctly overlapped and fixed. A chimney with four sides in contact with the roof has four potential failure points.
  • Valleys. Where two roof slopes meet, the valley channels water from both sides. Lead valleys, correctly dressed into a gutter profile with adequate laps, are long-lasting and robust. Where valleys have been done in mineral felt or cut tile, upgrading to lead is a sensible long-term investment.
  • Dormers. Dormers have multiple junctions including the cheeks where the side walls meet the main roof slope, the head where the dormer roof meets the main roof, and sometimes a flat or sloped dormer roof itself. Each junction is a potential entry point, and dormers are one of the areas where poor leadwork shows up most quickly.
  • Flat roof abutments. Where a flat roof meets a wall, a lead flashing tucked into the masonry and dressed down over the roof edge seals the junction. Without it, water tracks behind the upstand and enters the building at the wall base.
  • Parapet walls and copings. On properties with parapet walls, lead is used to waterproof the top of the parapet and the gutter behind it. Parapet leadwork takes a particularly heavy beating from weather and UV because it is often fully exposed from above.
  • Pipe flashings and penetrations. Where soil pipes, vents or other penetrations come through a roof slope, a correctly fitted lead slate or collar seals around the pipe. These are small but important pieces; a failed pipe flashing is a direct entry point for rainwater.

What the Work Involves

Lead work is not a material you can apply quickly. It is cut and dressed on site to fit the exact geometry of each junction. Where a chimney flashing is being replaced, the roofer will rake out the mortar joints to the correct depth, cut each piece of lead to size, dress it by hand into the required profile, tuck it into the raked joint, secure it with lead wedges, and then repoint over it with mortar. Each step has to be done correctly, because errors are hidden once the mortar goes back in.

On a valley, the existing lead or alternative material is stripped out, the boarding or underlay beneath is inspected, and new lead is dressed in section by section with the correct laps and drips to handle the volume of water the valley carries. If any boarding has rotted through water entry, that needs to be replaced before the new lead goes down.

On a dormer, the work often involves removing and re-seating the cheek cladding to allow the lead to be tucked correctly beneath it, rather than just surface-dressed over the top. Surface-dressed lead looks fine initially but does not provide a sealed joint and will fail much faster.

How Much Does Lead Work Cost?

Lead is not a cheap material, and the labour involved in cutting and dressing it on site is skilled work. For a standard chimney flashing replacement on a typical house, costs typically range from around £400 to £900 depending on the size of the stack, the number of pieces required, and the condition of the masonry. A valley replacement in lead typically costs between £600 and £1,500 for a standard run, depending on length and access. These are indicative figures and any quote should set out what is and is not included.

When comparing quotes, check whether the price includes raking out and repointing mortar joints, replacing any rotten boarding beneath, and all lead clips and fixings. A quote that simply states "replace chimney flashing" without specifying these items may not cover everything the job requires.

Repair or Full Replacement?

Not every leadwork problem requires a complete replacement. If a flashing has failed at one point because a clip has corroded or mortar has fallen out, and the lead sheet itself is otherwise sound, a targeted repair may be entirely appropriate. Lead that is cracked, split, or significantly corroded, or that has been poorly installed from the outset, is better replaced in full. Patching cracked lead with sealant or repair tape is a temporary measure; it will not hold indefinitely at a point where the metal is fatigued.

A roofer assessing the work should be able to tell you clearly which sections are serviceable and which need replacing, and explain why. If you are told everything needs replacing without any explanation of what is wrong with it, it is reasonable to ask for the specific reasons.

Questions to Ask Before the Work Starts

Before agreeing to any leadwork job, it is worth asking a few straightforward questions to make sure the scope and specification are clear.

  • What code of lead will be used, and why is that the right choice for this application?
  • Will the mortar joints be properly raked out and repointed, or will the flashing be surface-fixed?
  • Will any rotten or damaged boarding beneath the lead be replaced as part of the job?
  • How will the lead be secured, and what fixings will be used?
  • Is the price fixed, or are there potential additional costs if further problems are found once work starts?

Get Your Lead Work Checked in Red Lodge

Mildenhall Roofers carry out lead work on chimneys, valleys, dormers and flat roof abutments for homeowners in Red Lodge and the surrounding area. If you have spotted any of the warning signs described above, or if it has simply been a while since your leadwork was inspected, call us to arrange a roof survey so we can tell you exactly what the situation is and what, if anything, needs to be done.

Why choose Mildenhall Roofers?

  • Free survey and itemised quote
  • Fixed price - no surprises
  • Local team

Get your free quote

No obligation · We'll call you to arrange a free visit

By submitting you agree to being contacted about your enquiry. No spam, ever.

Urgent leak or storm damage?

Call any time. Calls are answered day and night and passed straight to our roofers.

Call now: 01638 597994