If your chimney stack in Beck Row is showing cracks, damp patches or loose brickwork, a rebuild from Mildenhall Roofers could stop a small problem becoming a costly one.
Call any time. Calls are answered day and night and passed straight to our roofers.
A chimney that looks solid from the ground can hide serious problems at stack level. Mortar erodes, bricks spall, and flashings fail - and by the time you notice damp on an internal wall or ceiling, water has usually been getting in for some time. Catching the signs early is the difference between a straightforward rebuild and much more disruptive remedial work inside your home.
These are the things worth checking from the ground, or from an upstairs window if you can get a safe angle:
Chimneys take more punishment than almost any other part of a house. They stand proud of the roofline, fully exposed to wind and rain on all four sides, with no shelter from overhanging eaves. The top of the stack - the area above the roofline - suffers the worst of it.
Frost damage is a major cause of deterioration. Water soaks into mortar joints and brickwork, then expands as it freezes. Over many winters this breaks the mortar bond and pushes brickwork apart from the inside. Stacks that face into prevailing weather take on more water and fail faster.
Heat cycling is another factor, particularly on chimneys serving solid-fuel appliances, wood burners or open fires. The stack heats up when the fire is lit and cools down when it is not. Repeated expansion and contraction stresses the mortar joints and, over years, works them loose. Chimneys that are rarely used can actually suffer more from damp than those used regularly, because a warm flue dries from the inside out.
Sulphate attack is common on older stacks. Combustion gases - especially from solid fuels - contain sulphates that gradually react with lime mortar and break it down. The mortar swells and then crumbles. This is more pronounced in stacks that have never been relined and where flue gases have direct contact with the masonry.
Biological growth adds to the problem. Moss, algae and lichens hold moisture against the brickwork and accelerate mortar erosion. A green chimney is one that is staying wet longer than it should.
If you use a solid-fuel appliance, a wood burner or an open fire, getting the chimney swept before any rebuilding work is assessed is important. A sweep clears soot, debris and any bird nest material so that the flue can be properly inspected. Blocked or partially blocked flues create back-draught and increase the risk of carbon monoxide entering the living space. A sweep also reveals whether the flue lining is sound or whether relining needs to be factored into the rebuild scope.
When we assess a chimney for rebuilding, the condition of the flue - and whether it has a liner - is part of what we look at. A rebuilt stack with a failing or absent liner is only half a job.
Not every chimney with failing mortar needs a full rebuild. The extent of the work depends on how far deterioration has progressed:
We use matching brick wherever possible to keep the rebuilt section in keeping with the original house. Mortar mix matters too: a mortar that is too hard for older, softer bricks causes the bricks to spall rather than the mortar to give way, which is the wrong outcome. Getting the mix right for the existing masonry is part of doing the job properly.
A rebuilt stack is only weathertight if the flashing at its base is sound. Lead flashing is cut into the mortar joints of the stack and lapped over the roof covering, creating a stepped and continuous seal around the perimeter. Old or cracked lead, or flashing that has simply been bedded in mortar without being properly fixed, will let water through regardless of how well the stack above it is built.
When we rebuild a chimney, we always assess the flashing at the same time. If it is failing, it is replaced as part of the job. Leaving old flashing on a new stack is a false economy.
As a rough guide, a partial chimney rebuild in this area - taking the stack down to flashing level and rebuilding with matching brick - typically costs in the range of £1,500 to £3,500, depending on the height of the stack, the access required, how much of the stack needs to come down, and whether the flashing needs replacing too. A full stack rebuild or one on a tall or complex roof will cost more. Scaffolding is usually needed for safe working at chimney height, and this is a meaningful part of the total cost on any chimney job.
These are honest ranges for typical domestic work. The only way to get an accurate figure is to have the chimney inspected directly - call us to arrange a roof survey and we will give you a straight answer on what needs doing and what it is likely to cost.
Can I just cap off a chimney I no longer use? Yes, and it is sensible to do so rather than let an unused stack deteriorate and let water in. A capped stack still needs the brickwork to be sound so that the cap stays weathertight.
Do I need to have the chimney swept before you inspect it? For a visual inspection of the exterior and flashing, no. If you want us to assess the flue interior or if there is any question of relining, a sweep first makes the inspection more useful.
Will the new brickwork match the original? We source matching brick wherever possible. On older properties the match is rarely perfect, but a good brick match gets close enough that the rebuilt section does not stand out.
How long will a rebuilt chimney last? A well-built chimney stack using appropriate materials and correctly mixed mortar should give many decades of trouble-free service. The flashing is typically the first element to need attention again, and lead flashing has a long service life when properly fitted.
No obligation · We'll call you to arrange a free visit
Call any time. Calls are answered day and night and passed straight to our roofers.