If your chimney stack in Isleham needs rebuilding, here is exactly what the job involves at every stage - from the first inspection to the point we pack up and leave your property clean.
Call any time. Calls are answered day and night and passed straight to our roofers.
A chimney rebuild is not a job you can watch from inside the house. Most of the work happens above the roofline, out of sight, and homeowners are understandably cautious about what they are agreeing to. Knowing what each stage involves, what decisions you need to make and what to expect at the end of each day helps you stay informed and confident throughout.
We carry out chimney rebuilds in Isleham, Mildenhall, Freckenham, Kennett, Soham and the villages nearby. The process is broadly the same on every job, though the detail varies with each chimney. Here is how a typical rebuild unfolds.
The job starts from the ground before anyone gets on a roof. A pair of binoculars and a good eye can reveal a lot: the general condition of the brickwork, obvious spalling, leaning, missing mortar or a loose pot. Damp patches on the chimney breast wall or ceiling inside the house are also assessed at this point, because they help identify where water is getting in and how far it has tracked.
A proper inspection also looks at whether the chimney is in use. If it serves a solid-fuel appliance, a wood burner or an open fire, the flue condition matters as much as the external brickwork. We will ask whether the chimney has been swept recently. If it has not, a sweep before the detailed inspection is worthwhile - a clean flue can be assessed properly, and a blocked or partially blocked flue is both a fire risk and a carbon monoxide risk.
On properties where the chimney is accessible via a flat roof or velux area, we can often get closer without scaffolding at this early stage. On most two-storey properties, though, the inspection is primarily ground-level and from inside the loft if there is access.
Once the extent of the problem is clear, we discuss what needs doing and why. For a partial rebuild - the most common scenario - this means agreeing how far down the stack needs to come, what brick to use, the mortar mix, whether the flashing needs replacing, and what happens at the top (pot, cap or cowl).
If the chimney serves a solid-fuel appliance or a wood burner, the flue liner is part of this conversation. Many older chimneys have no liner, or have a liner that has corroded or cracked. Fitting a new flexible stainless steel liner during a rebuild makes sense because the scaffolding is already in place - doing it separately later means a second scaffold cost.
At this stage we also agree on brick matching. If you want reclaimed brick to match the original, say so now - sourcing it takes time and affects the programme. If a new brick is acceptable, the choice is quicker and the job can start sooner.
Chimney work cannot be done safely from a ladder alone. A scaffold tower or a full scaffold lift is erected around the affected area of the roof. On most domestic properties this means a scaffold tied to the fascia or guttering, with a working platform at or just below ridge height. The scaffold is erected by a specialist subcontractor and takes a morning to put up on a standard two-storey house.
The scaffold stays in place for the duration of the job and is struck once the work is complete and signed off. The cost of scaffolding is a real and significant part of the total price for any chimney job - it is not something that can sensibly be cut out. Any contractor claiming to rebuild a chimney from a ladder alone is not working safely.
The existing stack is carefully dismantled from the top down. Bricks are lowered rather than dropped - both for the safety of anyone below and to preserve any bricks that are worth reusing. The chimney pot is removed first, then the stack is taken down course by course to the agreed level, which is usually just above the flashing line.
Once the stack is open, we can see the condition of the flue from above. This is the point at which the liner condition - or absence of a liner - becomes clear. If the scope needs to change at this point (for example, if the stack needs to come down further than expected), that conversation happens on the day before any further work proceeds.
Rubble and old mortar are collected as the work progresses. Bricks that are usable for infill or hardcore are set aside; the rest is bagged for disposal.
If the lead flashing is being replaced - which it usually is on a chimney that has deteriorated to the point of needing a rebuild - this is done before the new stack goes up. The lead is cut to the correct profile, stepped into the mortar joints of the remaining masonry and lapped over the roof covering on each side. The back gutter or soaker at the top of the stack is fitted at the same stage.
New lead takes a short time to oxidise and settle into its final appearance. Code 4 lead is the minimum for chimney flashings; Code 5 is used in more exposed situations. The lead is fixed into the mortar joints using lead plugs or wedges and then pointed over - not just bedded in mortar without fixings, which is a common short-cut that fails.
The new brickwork goes up course by course. Each course is checked for level and plumb. Mortar joints are kept consistent in width and are finished to match the original where possible. The mortar mix is chosen to suit the existing bricks - a harder mix than the bricks can handle will cause spalling over time.
If a flue liner is being fitted, it is fed down from the top during the build. The liner is secured at the top with a liner clamp and at the bottom to the appliance or register plate. The space between the liner and the flue walls is sometimes backfilled with a lightweight insulating concrete to prevent condensation between the liner and the stack.
The chimney pot is set in fresh mortar at the top of the stack. The haunching - the mortar fillet that slopes away from the pot and sheds water off the top of the stack - is formed at this stage. A flat or poorly formed haunch holds water and accelerates mortar breakdown at the stack top.
Once the mortar has cured, the stack is inspected from the scaffold platform. Joints are checked, the flashing laps are confirmed and the pot seating is verified. If a liner has been fitted, a smoke test can be carried out to confirm there is no leakage at any joint. For a chimney serving a solid-fuel appliance or a wood burner, this is a useful step before the appliance is used.
If the chimney has not been swept recently and is being returned to service, a sweep at this point is advisable. A clean flue with a confirmed sound liner is the right starting point for any heating season.
All debris, off-cuts of lead, old mortar and redundant materials are cleared from the roof and from around the property. The scaffold is struck once the work is signed off, and any minor marks to guttering or fascias from the scaffold feet are made good.
By the end of the job the only change visible from the ground should be the new brickwork - and if the brick match is good, even that should be hard to spot at street level.
A partial chimney rebuild in the Isleham and Mildenhall area - taking the stack down to flashing level and rebuilding with matching brick - typically falls in the range of £1,500 to £3,500 for a standard domestic chimney. A full rebuild or work on a taller or more complex roof will cost more. Adding a new flexible stainless steel liner typically adds £500 to £1,200 to the overall cost depending on flue length and diameter. Scaffolding is a significant part of the total and is unavoidable on chimney work at height.
Call us to arrange a roof survey in Isleham. We will inspect the chimney, explain what we find and give you a clear picture of what the job involves before any work is agreed.
If your chimney has been swept regularly, the liner and flue are already in a known condition before the rebuild starts - which makes scoping the job easier. If you burn solid fuel or use a wood burner and have not had the chimney swept in the last twelve months, it is worth arranging a sweep before or immediately after the rebuild. Burning unseasoned wood in particular leads to rapid tar and soot build-up on flue walls, and a blocked flue after a fresh rebuild is a frustrating and avoidable problem.
No obligation · We'll call you to arrange a free visit
Call any time. Calls are answered day and night and passed straight to our roofers.